Wednesday 15 February 2012

JTO QUESTION PAPERS

BSNL JTO (Junior Telecom Officers) Previous Year Question Paper

When a piece of copper and another of germanium are cooled from room temperature to 800 K then the resistance of -

a) Each of them increases

b) Each of them decreases

c) Copper increases and germanium decreases

d) Copper decreases and germanium increases

When a signal of 10 mV at 75 MHz is to be measured then which of the following instrument can be used -

a) VTVM

b) Cathode ray oscilloscope

c) Moving iron voltmeter

d) Digital multimeter

When a sample of germanium and silicon having same impurity density are kept at room temperature then –

a) Both will have equal value of resistivity

b) Both will have equal value negative resistivity

c) Resistivity of germanium will be higher than that of silicon

d) Resistivity of silicon will be higher than that of germanium

When an RC driving point impedance function has zeros at s= -2 and s=-5 then the admissible poles for the function would be –

a) s = 0; s = -6

b) s = 0; s = -3

c) s = 0; s = -1

d) s = -3; s = -4

For the n-type semiconductor with n = Np and p = , the hole concentration will fall below the intrinsic value because some of the holes –

a) drop back to acceptor impurity states

b) drop to donor impurity states

c) Virtually leave the crystal

d) recombine with the electrons

The location of lighting arrestor is –

a) Near the transformer

b) Near the circuit breaker

c) Away from the transformer

d) None

Time constant of an RC circuit increases if the value of the resistance is –

a) Increased

b) Decreased

c) Neither a nor b

d) Both a and b

Telemetering is a method of –

a) Counting pulses sent over long distances

b) Transmitting pictures from one place to another

c) Transmitting information concerning a process over a distance

d) None

When the gauge factor of a strain gauge is 2, stress is 1050 kg/cm2, Y = 2.1´ 106 kg/cm2 and R is 100 ohms then the value of DR will be -

a) 2W

b) 3W

c) 4W

d) 1W

As the drain voltage is increased for a junction FET in the pinch off region then the drain current –

a) Becomes zero

b) Abruptly decreases

c) Abruptly increases

d) Remains constant

11. One of the following, which is not a transducer in the true sense, is –

a) Thermocouple

b) Piezoelectric pick up

c) Photo-Voltaic cell

d) LCD

When a transistor is required to match a 100W signal source with a high impedance output circuit then the connection that would be used is –

a) Common base

b) Common collector

c) Common emitter

d) Emitter follower

In a JFET gates are always –

a) forward biased

b) reverse biased

c) unbiased

d) none

The main factor which differentiate a DE MOSFET from an E only MOSFET is the absence of –

a) insulated gate

b) electrons

c) channel

d) P-N junction

An SCR conducts appreciable current when –

a) Anode and gate are both negative with respect to cathode

b) Anode and gate are both positive with respect to cathode

c) Anode is negative and gate is positive with respect to cathode

d) Gate is negative and anode is positive with respect to cathode

Silicon is not suitable for fabrication of light emitting diodes because it is -

a) An indirect band gap semiconductor

b) A direct band gap semiconductor

c) A wide band gap semiconductor

d) A narrow band gap semiconductor

An average responding rectifier type electronic ac voltmeter has its scale calibrated in terms of the rms value of a sine wave, when a square wave voltage of peak magnitude 100V is measured using this voltmeter then the reading indicated by the meter, will be –

a) 111V

b) 100V

c) 90.09V

d) 70.7V

When a four terminal T network is inserted between a source and load resistance as shown in figure then the resistance seen by the source remain the same with or without the four terminal block when R is –

a) 5W

b) 10 W

c) 15 W

d) 20 W

Which one of the following conditions for Z parameters would hold for a two port network containing linear bilateral passive circuit elements –

a) Z11 = Z22

b) Z12Z21 = Z11Z22

c) Z11Z12 = Z22Z21

d) Z12 = Z21

When the transmission parameters of the following network are A = C = 1, B = 2 and D = 3 then the value of Zin is –

a) 3W

b) 4W

While calculating Rth, constant current sources in the circuit are –

a) replaced by opens

b) replaced by ’shorts’

c) treated in parallel with other voltage sources

d) converted into equivalent voltage sources

Maxwell’s loop current method of solving electrical networks –

a) uses branch currents

b) utilizes kirchhoff’s voltage law

c) is confined to single-loop circuits

d) is a network reduction method

A transmission line of characteristic impedance Z0 = 50 ohms, phase velocity Vp = 2 x 108 m/s and length l = 1m is terminated by a load ZL= ( 30 – j 40 ) ohms. The input impedance of the line for a frequency of 100 MHz will be

a)(30 + j40 ) ohms

b)( 30 – j40 ) ohms

c)(50 + j40 ) ohms

d)(50 – j40 ) ohms

For an elliptically polarized wave incident on the interface of a dielectric at the Brewster angle then the reflected wave will be-

a) Elliptically polarized

b) Linearly polarized

c) Right circularly polarized

d) Left circularly polarized

A yagi antenna has a driven antenna-

a) Only

b) With a reflector

c) With one or more directors

d) With a reflector and one or more directors

The number of lobes on each side of a 3l resonant antenna is –

a) 3

b) 6

c) 2

d) 1

The electric field intensity of a Hertizian dipole at a remote point varies as -

Radiation resistance of a half wave folded dipole is -

a) 72 W

b) 144W

c) 288 W

d) 216W

When a carrier wave is modulated at 100% it’s power is increased by -

a)100%

b)150 %

c)50%

d)0%

On a clear sky day, the atmospheric radio noise is strongest -

a) During morning hours

b) Around mid-day

c) During nights

d) In the afternoon

TV broadcasting system in India is as per CCIR -

a) System B

b) System I

c) System M

d) System X

For the safety measurement of the internal resistance of a 25-0-25 mA meter, a laboratory multimeter whose sensitivity is equal to –

a) 1k ohm/volt can be used

b) 10 k ohm/volt can be used

c) 100 k ohm/volt can be used

d) 200 k ohm/volt can be used

In order to measure moisture in wood the most suitable method is –

a) Electrical conduction

b) Electrical – capacitive

c) Absorption of radiation

d) Equilirium- moisture vs humidity

The flow rate of electrically conducting liquid without any suspended particle cannot be measured by –

a) turbine flow meters

b) electromagnetic flow meters

c) ultrasonic flow meters

d) thermistor based heat loss flow meters

The most useful transducer for displacement sensing with excellent sensitivity, linearity and resolution is –

a) an incremental encoder

b) an abosolute encoder

c) LVDT

d) a strain gauge

When variable reluctance type tachometer has 150 teeth on the rotor & the counter records 13,500 pulses per second then the rotational speed will be–

a) 4800 rpm

b) 5400 rpm

c) 6000 rpm

d) 7200 rpm.

41. On a voltage scale, zero dB m in a 600-ohm system could refer to –

a) 1.732 V

b) 1.0 V

c) 0.7746 V

d) 0.5V

One of the following devices which is required in addition in order to measure pressure using LVDT is-

a) strain gauge

b) pitot tube

c) Bourden tube

d) Rotameter

It is required to measure temperature in the range of 13000 C to 15000 c) The most suitable thermocouple to be used as a transducer would be –

a) chromel - constantan

b) Iron - constantan

c) chromel - alumel

d) platinum- rhodium

In a CSI if frequency of output voltage is f Hz, then frequency of input voltage to CSI is-

a) f

b) 2 f

c) f/2

d) 3 f

Identify the type of chipper in the given circuit

a) Type A chopper

b) Type B chopper

c) Type C chopper

d) Type D chopper

Maximum value of charging resistance in an UJT is associated with-

a) peak point

b) valley point

c) any point between peak and valley

d) after the valley point

Thyristor A has rated gate current of 2A and thyristor B a rated gate current of 100 mA-

a) A is a GTO and B is a conventional SCR

b) B is a GTO and A is a conventional SCR

c) B may operate as a transistor

d) none of the above

In a 3 phase full converter, the output voltage during overlap is equal to-

a) zero

b) source voltage

c) source voltage minus the inductance drop

d) average value of the conducting phase voltages

Mark old the correct statement for Cycloconverters-

a) step-down Cycloconverter (CC) works on natural commutation

b) step up CC requires no forced commutation

c) load commutated CC works on line commutation

d) none of the above

In the RF amplifier stage cascade (CE-CB) amplifier is used because it gives-

a) Large voltage gain

b) Low output impedance

c) Large isolation between the input and the output

d) None of the above

Silicon diode is less suited for low voltage rectifier operation because-

a) it can withstand high temperature

b) ensures low PIV of the diodes

c) ensures lower values of capacitance in the filter

d) reduces ripple content

An amplifier of class A is that in which -

a) Base is biased to cut – off

b) Ic flows most of the time

c) Ie flows all the time

d) Vc often raises to Vcc

A transistor is in active region when-

a) IB = bIC

b) IC=bIB

c) IC=IE

d) IC=IB

For coupling purposes in RF amplifier a buffer amplifier is used because it provides-

a) Maximum loading and minimum mismatch

b) Minimum loading and minimum mismatch

c) Maximum loading and maximum mismatch

d) Minimum loading and maximum mismatch

A transistor has CE parameter as hie = 10kW, hre =20 x 10-4 , hse = 100, hoe = 25 ms. The hib for this transistor will be-

a) 100 W

b) 99.01 W

c) 5m W

d) 101kW

An FM radio receiver is tuned to a 90.6 MHz broadcast station. It will receive an image frequency of -

a) 110 MHz

b) 112 Hz

c) 114 MHz

d) 120 MHz

In the given fig RL is shorted out, then VCE will become-

a) OV

b) VCC – IBRB

c) Equal to VCC

d) None of the above

See the circuit shown and choose the correct option –

a) Only red will glow

b) Only green will glow

c) Both red and green will glow

d) Neither red nor green will glow

A dc to dc converter having an efficiency of 80% is delivering 16W to a load) If the converter is generating an output of 200V from an input source of 20V, then the current drawn from the source will be –

a) 0.1A

b) 0.5A

c) 1.0A

d) 10.0A

A transistor is operated as a non-saturated switch to eliminate –

a) storage time

b) turn – off time

c) turn – on time

d) delay time

The output Y of the circuit in the given figure is –

a) (A + B)C + DE

b) AB + C(D + E)

c) (A + B)C + D + E

d) (AB + C) . DE

Rotors used in a two-phase ac servomotor is –

a) solid iron motor

b) squirrel cage rotor

c) drag cup rotor

d) both b and c

Major advantage of TWT over a klystron lies in its –

a) higher bandwidth

b) higher output

c) higher frequency

d) higher gain

The op-map circuit shown in the given figure can be used for –

a) addition

b) subtraction

c) both addition and subtraction

d) multiplication

The Boolean expression for the shaded area in the given Venn diagram is –

A lag compensator is basically a –

a) high pass filter

b) band pass filter

c) low pass filter

d) band elimination filter

Transfer function T (S) of the system in the given fig is-

The overall transfer function for a unity feedback system is

Mark the correct statement regarding this system

1. Position error constant kp for the system is 4

2. The system type one.

3. The velocity error constant kv for the system is finite.

Select the correct answer using the codes given below- Codes

a) 1,2 and 3

b) 1 and 2

c) 2 and 3

d) 1 and 3

If the rotor’s resistance and reactant’s are respectively R and X1 its length and diameter are L and D for two phase a) c) servomotor, then-

In a PID controllers the transfer function G(s) is-

Transfer function can be approximated by the system- The transfer function of an amplifier is given by The high 3 db frequency of an amplifier will be approximately-

a) 5850 kHz

b) 585 kHz

c) 5850 Hz

d) 585 Hz

An open loop transfer function is given by Its – loci will be-

The output signals amplitudes for 1’s and 0’s in an ADM transmission systems are –

a) Fixed and the repetition rate is also fixed

b) Fixed but the repetition rate is variable

c) Variable and the repetition rate is also variable

d) Variable but the repetition rate is fixed

Microwave link repeaters are typically 50km apart –

a) Because of atmospheric attenuation

b) Because of Output tube power limitations

c) Because of the earth’s curvature

d) To ensure that the applied ac voltage is not excessive

The amplifier inserted at intervals to amplify the signal and compensate for transmission loss on the cable are called-

a) line amplifier

b) equalizing amplifiers

c) compradors

d) repeaters.

Diversity reception in used to-

a) increase receiver sensitivity

b) improve receiver selectivity

c) overcome degrading effect of fading

d) overcome degrading effect of receiver detuning

Mark out transferred electron device in the following-

a) BARITT dived

b) IMPATT dived

c) Gunn divde

d) Step recovery diode

In the output of a normal monochrome receiver video detector voltages, which are not found, are -

a) syne

b) video

c) sweep

d) sound

The HV anode supply for the picture tube of TV receiver is generated in the-

a) mains transformer

b) vertical output stage

c) horizontal output stage

d) horizontal deflection oscillator

In antenna measurements using two aperture antennas of dimensions D1 and D2 , minimum separation between the two should be (x is free space wavelength of radiation uses) The frquency range for satellite broad casting is –

a) 30 MHz – 300MHz

b) 30 MHz – 3 GHz

c) 3 GHz – 30 GHz

d) 30 GHz – 300 GHz

Iris is used to –

a) Over come power loss

b) Over come bending effect

c) Over come mismatch error

d) Over come twist effect

In schotty barrier diode current flows because of –

a) Majority carriers

b) Minority carriers

c) Majority and minority carriers

d) None

Which antennas are used in microwave communication –

a) long wave antennas

b) Rhombic antennas

c) Parabolaidal antennas

d) All of above

Among translator & time of sight system capacity –

a) Of translator is more

b) Of line of sight is more

c) Having equal capacity

d) No relation such as

No of T-state required for memory read or write operation-

a) 2

b) 3

c) 4

d) 6

In data transfer operation which flag get affected-

a) 3140 flog.

b) carry flog

c) sign flog.

d) none

The storage and retrieval of data on stacks should follow sequence-

a) last in first out

b) first in first out

c) random in random out

d) none

While executing program microprocessor checks INTR line clearing-

a) each instruction

b) after interval of two instruction

c) after a subroutine

d) at the end of program.

93. In which error check technique of data communication 2’s complement of all bytes of data is transmitted with data-

a) Even parity

b) odd parity

c) check scans

d) cyclic redundancy

Program execution hierarchy decides which operator-

a) is most important

b) is used first

c) is fastest

d) operators on largest number

(375)10 = (—-)8

a) 550

b) 557

c) 567

d) 577

To obtain 2048 8 memory using 128 8 memory chip how many IC required-

a) 2

b) 4

c) 8

d) 16

A Decimal no. 17 can be converted in binary, the binary no. will be.-

a) 10001

b) 01110

c)00111

d) 11100

Is the Universal logic gate-

a) AND

b) OR

c) NAND

d) X-OR

A monostable state in multivibrator means-

a) which returns itself to its single stable state

b) the state used only once in circuit

c) the state of circuit can not get changed

d) the state of circuit always changing

For designing binary counter which flip flop is preferred -

a) T FF

b) SR FF

c) D FF

d) JKFF

His handwriting was not —– so I could not read his note –

a) attractive

b) eligible

c) clear

d) legible

They started to —– people into the theatre only at six -

a) enter

b) admit

c) follow

d) accept

I told him to buy things that are lasting (Give the appropriate synonym of the underlined word).

a) ending

b) ordinary

c) durable

d) cheap

Give the word which is most opposite in meaning of the word ‘evident’-

a) doubtful

b) unimportant

c) disagreed

d) understood

I expressed by disagreement —— him on that issue-

a) between

b) with

c) about

d) for

‘Sugarbowl’ of the world is -

a) India

b) Cuba

c) Brazil

d) USA

Palk strait separates-

a) India and Srilanka

b) India and Burma

c) Britain and France

d) Malaysia and Sumatra

The minimum number of atoms in a molecule of an element are-

a) 1

b) 5

c) 2

d) 10

Tides in the sea are caused by-

a) Effect of sun

b) Effect of moon

c) combined effect of moon and sun

d) Gravitational, centrifugal and centripetal forces

The Bar council of India decided to close over law colleges across the country for their failure to maintain minimum teaching standard) There number is

a) 140

b) 200

c) 150

d) 100

Aswan Dam is located in-

a) Egypt

b) Libya

c) Sudan

d) Iran

Ghana Birds sanctuary is in the state of -

a) Rajasthan

b) Madhya Pradesh

c)Uttar Pradesh

d) Maharashtra

Dry ice is-

a) Frozen carbon monoxide

b) Frozen carbon dioxide

c) Frozen ammonia

d) None of these

East flower river of India is -

a) Cauvery

b) sone

c) Narmada

d) Tapti

The total length of the great wall of China is –

a) 1,400 miles

b) 1,500 miles

c) 1,300 miles

d) 1,400 miles

Deficiency of vitamin C may result in-

a) beriberi

b) night blindness

c) dermatitis

d) Scurvy

Bharat Shah a film financer was granted bail by Supreme Court after a

period of –

a) 11 months

b) 2 years

c) 18 months

d) 15 months

Indian local time is based on-

a) 800 E longitude

b) E longitude

c) 1100 E longitude

d) 250 E longitude

The two days Shiv Shena Mahashivir of 2002 started at Shirdi on –

a) 9th April 2002

b) 10th April 2002

c) 8th April 2002

d) 11th April 2002

Which one is a good preservative of food?

a) Spirit

b) Formaldehyde

c) Sugar


Monday 23 January 2012

Questions of 2012

GENERAL QUESTIONS OF 2012
1)What is name of NGO with which Anna Hazare is associated?
Ans: India Against Corruption
2)With which country India recently signed an agreement on technology transfer.

Ans: Oman
3)How many pacts India recently sign with China during Chinese Premier Wen Jiabao’s visit to India?

Ans: Six Pacts
4)India has became a part of $ 10 billion Gas pipeline project, the project is backed by which country?

Ans: U. S. A.
5)Recently Union Government has launched a Project-15 B. This project is related to…..?

Ans: Defence Programme
6)Grand Central Terminal, Park Avenue, New York is the world’s?

Ans: largest railway station
7)Eritrea, which became the 182nd member of the UN in 1993, is in the continent of?

Ans:Africa
8)Which gas is used to fill the tyre of aeroplane?

Ans: Helium
9)Who has written the Miser?

Ans: Moliere
10)Hitler party which came into power in 1933 is known as?

Ans: Nazi Party
11)Which river has played an important role in building the Punjab ?

Ans: Sutlej
12)Indian Standard Time line passes through which of the following towns?

Ans: Allahabad
13)Where is the headquarter of ‘Forest Research Centre’ situated?

Ans: Dehradun
14)Open Museum of ‘Hampi’ is situated in which of the following states?

Ans: Karnataka
15)In which of the following cities is ‘Bhabha Atomic Research Centre’ situated?

Ans: Mumbai
16)Which liquid is used in manufacturing dynamite?

Ans: Nitroglycerine
17)What is used in bleaching and manufacturing of food?

Ans: Caramel
18)Which of the following digits makes the binary System?

Ans: 0 and 1
19)In which state is Mahabaleshwar located

Ans: Mahrashtra
20)Ayappa Temple is situated in which of the following cities?

Ans: Kerala
21)Guru Arjun Dev was the contemporary of which leader?

Ans: Jehangir
22)Goutamiputra Satkarni was the king belongs to which dynasties?

Ans: Satwahan
23)Goitre is a disease is related to which part of body.

Ans: Neck
24)What is the chemical name of Washing Soda?

Ans: Sodium carbonate
25)Where is Humayun tomb located?

Ans: Delhi
26)Which personality was given the title of ‘Jari Kalam’?

Ans: Mukammal Khan
27)Which crops has the largest interval between sowing and reaping it?

Ans: Sugarcane
28)Which of the following diseases is not immunized by ‘triple antigen’?

Ans: Tetanus
29)Which of the following is the chemical name of laughing gas?

Ans: Nitrous oxide

BSNL SOLVED Q&Ans

BSNL (JTO) Exam Solved Question Paper
by
GR.RAJTHILAK

Q.1 A house served by a 220V supply light, is protected by a 9-Ampere fuse. The maximum number of 60 W bulbs in parallel
that can be turned on is
(a) 11 (b) 33
(c) 22 (d) 44
Q.2 An n-channel JFET has IDSS
= 1 µA & VP
=–5V. The maximum transconductance is
(a) gm
= 0.4 milli mho (b) gm
= 0.04milli mho
(c) gm
= 0.04 mho
(d) gm
= 0.4 millimilli mho
Q.3 The base to base resistance of a UJT is 6 K Ohm when the emitter current is zero. If B1 R = 3.6 K Ohm, the intrinsic stand off ratio is
(a) n = 0.66 (b) n = 0.6
(c) n = 6.0 (d) n = 3.6
Q.4 A capacitor of 1µF initially charged to 10 V is connected across an ideal inductor of 0.1 mH. The maximum current in the circuit is
(a) 0.5 A (b) 1 A
(c) 1.5 A (d) 2 A

Q.5 Silicon has a preference in IC technology because
(a) it is an indirect semiconductor
(b) it is a covalent semiconductor
(c) it is an elemental semiconductor
(d) of the availability of nature oxide SiO
Q.6 Three equal resistance of magnitude 5 Ohm each are connected in delta. The resistance between any two pair of terminals of the delta will be
(a) 5 Ohm (b) 5/3 Ohm
(c) 10/3 Ohm (d) 3/5 Ohm
Q.7 The R.M.S. value of a half wave rectified sinusoidal alternating current with peak value Im is
(a) Im/1 (b) mI / 2
(c) mI / 2 (d) mI 3
BSNL JTO Exam (Memory Based Questions)
Q.8 For a series resonant circuit, at the half power points,which of the following is true?
(a) Current is half of the current at resonance.
(b) Resistance is equal to the reactance.
(c) The impedance is half the impedance at the resonance.
(d) None of the above
Q.9 The lossless line of characterstics impedance 300 Ohm is terminated in a pure resistance of 200 Ohm. The value of the
standing wave ratio is
(a) 1.5 (b) 0.67
(c) 1.0 (d) 1.25
Q.10 The transient current in lossless L-C circuit when excited from an AC source is, sine wave
(a) Critically damped (b) Underdamped
(c) Overdamped (d) Undamped

Sunday 22 January 2012

BSNL PLACEMENT TIPS

BSNL - JTO Placement Preparation Tips and Placement Process

The selection of candidates into the BSNL JTO post is done on the basis of an All India Competitive Examination. Students who score good marks will be short listed and called for an interview. The placement procedure contains 4 stages. Each stage has its own difficulty. Applicants who clear all the 4 steps in the selection procedure shall be given the final call letter.
BSNL - JTO Placement Test
The BSNL – JTO paper is divided into 3. The question distribution is mentioned below.
BSNL Recruitment for JTOs (Telecom)
  • Part - I : Engineering stream - 50
  • Part - II : Engineering stream - 50
  • Part - III : General Ability Test - 20
For JTOs (Electrical)
  • Part -I : Electrical Engineering stream - 50
  • Part -II : Electrical Engineering stream - 50
  • Part -III : General Awareness - 20
Recruitment in BSNL JTOs (Civil)
  • Part -I : Civil Engineering stream - 50
  • Part -II : Civil Engineering stream - 50
  • Part -III : General Ability Test - 20
The question paper of the BSNL JTO exam will be completely of the objective nature. Its syllabus will be similar to that of the Engineering Examination carried out by any Indian university.
BSNL - JTO Placement Interview
Once the applicant has cleared the written test, the Technical Interview is the next round for them in the selection procedure. In this interview, applicants will be questioned about the subjects they have studied so far. They might be asked questions about the project that they have done. The HR interview will follow this round.
BSNL - JTO Placement Test Preparation Tips
Questions of general nature will be asked in the written part of the interview procedure. One can consider this as the easiest part in the selection procedure. Numerous competitive exam guides will be available for providing help for the candidates. One of the best reference books includes R.S.AGARWAL’s. The Psychometric Test will contain 150 questions which the candidates need to finish answering within 30 minutes. Candidates need to be honest when they are answering the questions asked. This is because the main intention of the psychometric test is to determine the aptitude of the applicant.
BSNL - JTO Placement Interview Preparation Tips
If the applicant has cleared all the tests then the next thing for them to do is to perform well in the interview. One can never expect what the firm will ask, so they need to be very well prepared in advance. Applicants will be asked technical questions in addition to questions on the projects they did. While answering each question, students need to be sure that they answer clearly and without hesitation. In case the applicants get a chance to ask a question about the firm and its functions to the judging panel, students must make use of this opportunity. The final round of the interview process will be the HR round. To be successful in this round, applicants need to come prepared with self introduction, their role models, their strengths and other abilities etc.
ALL THE BEST FOR YOUR FUTURE
BY
GR.RAJTHILAK
All India Jobs Facebook Page